News

The correct use of handheld fiber laser welding machine

With the laser welding technology is widely used in various industries, laser welding machine fast welding efficiency, gradually replaced the traditional welding equipment, and by the majority of users love. Some users do not have a good grasp of laser welding machine precautions, it is easy to greatly reduce the efficiency of the laser welding machine, and sometimes even let the laser welding machine can not be used properly. Handheld laser welding machine is often in contact with the welding equipment, as long as you master the use of the process should pay attention to matters, I believe that we can be more quickly applied to laser welding machine, better into the work. Follow GOLD MARK to understand the following.

The correct use of handheld fiber laser welding machine

1. Use process

Start-up process: open the air valve → open the air switch on the rear side of the equipment → release the panel emergency stop button → turn the key to the right side to open the system power → press the water machine power button → press the laser power button, wait 20 seconds and then you can use.

Welding process: clamp the welding protection chuck on the working table; check whether the process parameters are required for the current welding workpiece; click the “open valve” button on the interface of the control system to check whether the blowing flow meets the welding requirements; click the “start” button on the interface of the control system to test whether the light protection circuit is working normally (align the welding head with the test plate surface, press the light button, no light is normal; put the welding head in contact with the test plate surface, press the light button, light is normal); after the test is correct, you can start welding.

Shutdown process: Place the welding head on the welding head holder, click the “Stop” button on the control system interface, turn off the laser power button → turn off the water machine power button → turn the system power key to the left and pull out → press the emergency stop button → turn off the air switch on the rear side of the equipment → turn off the air valve.

2. Precautions

l Must wear radiation-proof glasses, masks, must wear safety clothing to ensure the safety of staff production, all safety accidents caused by irregularities and the company has nothing to do.

l Prohibit the use of common ground with arc welding machine (argon arc welding, electric welding, carbon dioxide shielded welding machine) to prevent the current reflux affect the laser components.

The correct use of handheld fiber laser welding machine1

l The welding head must not be aimed at any part of the body during use. The welding head cannot be placed on the ground, always pay attention to dust control.

l Pay attention to the bending radius of the fiber optic bellows cannot be less than 20CM during the welding process to avoid burning off the fiber.

l In case of any accident, press the emergency stop button immediately and contact our staff to reflect the situation.

l If you stop working temporarily, please click “Stop” to enter standby mode, or stop working after work, please click “Stop” to enter standby mode and turn off the equipment.

l When replacing the protective lens or checking the welding head, the power of the equipment must be turned off.

The temperature difference between the water temperature of the chiller and the room temperature should be no more than 10 degrees! The water temperature is recommended to be set to 26℃-30℃ in summer and 20℃-22℃ in winter. The temperature difference between the cabinet will cause the laser device to condense and cause damage to the laser. When the room temperature is lower than 4℃, you must take anti-freezing measures, you can add glycol and pure water into the water tank after mixing in the ratio of 1:3.

Jinan Gold Mark CNC Machinery Co., Ltd. is a high-tech industry enterprise specialized in researching, manufacturing and selling the machines as follows: Laser Engraver, Fiber Laser Marking Machine, CNC Router. The products have been widely used in advertisement board, crafts and molding, architecture, seal, label, woodcutting and engraving, stonework decoration, leather cutting, garment industries, and so on. On the base of absorbing the international advanced technology, we provide the clients the most advanced production and perfect after-sale service. In recently years, our products have been sold not only in China, but also as far as Southeast Asia, Middle east, Europe, South America and other overseas Markets.

Email:   cathy@goldmarklaser.com
WeCha/WhatsApp:   +8615589979166


Post time: Dec-10-2021